Product added to cart

10Hz to 100kHz, Dual Phase Lock-In Amplifier

Stock #55-784 聯絡我們
- +
Qty 1+
Volume Pricing
Request Quote
Operating Temperature (°C):
0 to +50
Width (mm):
Sine: 100 mV RMS min (15 V Max.)
Pulse: 5 V, 95% Mark/Space Ratio Min.
Time Constant:
Selectable: 100μs, 300μs, 1ms, 3ms, 10ms, 30ms, 300ms, 1s, 3s, 10s, 30s
Maximum Acquisition Time (s):
Mains voltage selection must be made to match users operating voltage.
Please refer to manual for instructions.
Depth (mm):
Phase Control:
90° Steps
0 - 100° Fine Shift Range
Phase Stability (°/°C):
Power Supply:
115V AC ±5% at 50Hz or 60Hz
230V AC ±5% at 50Hz or 60Hz
Frequency (Hz):
10 - 100,000
Gain (dB):
Gain Accuracy (%):
Gain Stability (ppm/°C):
Height (mm):
Input Impedance (kΩ):

Regulatory Compliance

Certificate of Conformance:


  • 透過模數(R)計算執行雙相位作業
  • 採用差動輸入或單端輸入
  • 增益設定範圍是3μV至1V
  • High Performance Wide Bandwidth Input Gain Stage
  • 針對X、Y或R輸出訊號的顯示採用類比儀錶
  • Separate X, Y and R Output BNCs
  • 採用X與Y偏移控制
  • 輸出時間保持恆定(從100μs至30s)
  • 1F and 2F Reference Signal Operation
  • 具有90°步進與精細相位控制

此類比雙相位鎖定放大器使用先進技術建立既具備多功能,又易於使用的高效能設備。鎖定放大器用於利用同步偵測程序來量測雜訊中所淹沒之訊號的幅度與相位,以恢復訊號。該放大器可充當窄帶帶通濾光片,移除大多數不需要的雜訊,同時允許要量測的訊號通過,從而實現上述功能。由參考訊號(必須向鎖定放大器提供參考訊號及未知訊號)設定要量測的訊號頻率,進而設定濾光片的通過頻寬範圍。The reference signal must be at the same frequency as the modulation of the signal to be measured. The front panel has three adjustment sections: Input, Output, and Reference. Power: 115V AC, 230V AC; 50-60Hz; 10VA max. Operating Temperature Range: 0-50°C. Amplifier operation can be split into 4 stages: an input gain stage, the reference circuit, a demodulator and a low pass filter.

The Input Signal Channel amplifies the input signal to a level suitable for the demodulator. High performance, low-noise, broadband amplifiers are used throughout. The input circuit can accept a differential or single-ended input via the front panel signal input BNC. Jumper options within the unit allow the outer BNC contact or screen to act as a high impedance differential input, as a low impedance (100 ohms) differential input or allow it to be connected to ground for single-ended operation. Through the careful design of the lock-in, up to ±10V of DC offset is allowed before saturation for gain settings from 1V to 300μV, ±1V of DC offset for gain settings from 100μV to 10μV and ±300mV of DC offset for the gain setting of 3μV.

The output of the signal input stage is processed using two very high bandwidth demodulators each operating 90° apart from each other to produce the X and Y signals. The X and Y outputs from the demodulator are passed through two first order, low pass filters and then amplified. The X and Y signals are combined to produce R the modulus signal, where R=(x2+y2)^½, before output via a front panel BNC.

The Reference Channel input circuitry uses a phase locked loop to lock on to a range of signals, such as TTL pulses or sinusoidal waveforms. A phase shifting circuit allows the reference signal to be moved with relation to the signal input. Signals at both the reference frequency and twice the reference frequency can be monitored.

Sales & Expert Advice
or view regional numbers
enter stock numbers to begin